venam
(This is part of the podcast discussion extension)

After a long hiatus, here it is:

Data Storage on Unix.


Link of the recording [ https://github.com/nixers-projects/podca...3?raw=true http://podcast.nixers.net/feed/download....10-151.mp3 ]

How is data is represented and read from permanent storage.

* https://en.wikipedia.org/wiki/File:IO_st...kernel.svg
* https://en.wikipedia.org/wiki/File_system
* https://help.ubuntu.com/community/LinuxF...sExplained
* http://linuxfinances.info/info/fs.html
* https://msreekan.com/2012/06/07/file-sys...odule-lkm/
* https://msreekan.com/2015/04/24/linux-storage-cache/
* http://www.ufsexplorer.com/und_fs.php
* http://www.cs.cmu.edu/~410-s07/lectures/...system.pdf
* https://jkmaterials.yolasite.com/resourc...IT-III.pdf
* http://www.netbsd.org/docs/internals/en/...ile-system
* http://www.porcupine.org/forensics/foren...pter3.html
* https://en.wikipedia.org/wiki/Cylinder-head-sector
* http://www.yolinux.com/TUTORIALS/LinuxTutorialSCSI.html
* http://www.tldp.org/HOWTO/html_single/SC...WTO/#intro
* https://unix.stackexchange.com/questions...si-and-ata
* https://www.kernel.org/doc/htmldocs/libata/
* https://www.linuxquestions.org/questions...308-print/
* https://www.freebsd.org/doc/handbook/geom-glabel.html
* https://www.cyberciti.biz/faq/freebsd-ha...formation/
* https://www.freebsd.org/cgi/man.cgi?quer...ormat=html
* http://nixdoc.net/man-pages/FreeBSD/ata.4.html
* https://www.freebsd.org/cgi/man.cgi?query=da&sektion=4
* http://www.webopedia.com/DidYouKnow/Comp...s_sata.asp
* https://insidehpc.com/2006/04/what-is-th...i-and-ata/
* https://en.wikipedia.org/wiki/SCSI
* http://linuxmafia.com/faq/Hardware/sata.html
* https://en.wikipedia.org/wiki/Serial_Attached_SCSI
* https://en.wikipedia.org/wiki/Parallel_ATA
* https://en.wikipedia.org/wiki/Serial_ATA
* https://en.wikipedia.org/wiki/Industry_S...chitecture
* https://en.wikipedia.org/wiki/Logical_block_addressing
* https://www.freebsd.org/doc/en/books/arc...block.html
* https://en.wikipedia.org/wiki/Device_mapper
* https://en.wikipedia.org/wiki/Disk_partitioning
* https://en.wikipedia.org/wiki/Partition_type
* https://en.wikipedia.org/wiki/Partition_table
* https://en.wikipedia.org/wiki/Master_boot_record
* https://en.wikipedia.org/wiki/BSD_disklabel
* https://wiki.archlinux.org/index.php/LVM#Introduction
* https://wiki.archlinux.org/index.php/Sof...ID_and_LVM
* http://www.tldp.org/HOWTO/Linux+FreeBSD-2.html
* https://en.wikipedia.org/wiki/Logical_Vo...er_(Linux)
* https://en.wikipedia.org/wiki/Virtual_file_system
* https://en.wikipedia.org/wiki/Fragmentat...gmentation
* http://www.tldp.org/LDP/lki/lki-3.html
* http://learnlinuxconcepts.blogspot.com/2...ystem.html
* http://www.tldp.org/LDP/sag/html/buffer-cache.html
* https://www.ibm.com/developerworks/libra...index.html
* https://en.wikipedia.org/wiki/Data_scrubbing
* https://en.wikipedia.org/wiki/Copy-on-write
* http://www.goop.org/~jeremy/userfs/
* https://en.wikipedia.org/wiki/File_descriptor
* http://linuxfinances.info/info/defrag.html
* http://www.tldp.org/LDP/tlk/fs/filesystem.html
* http://www.tldp.org/LDP/sag/html/filesystems.html
* http://man7.org/linux/man-pages/man5/filesystems.5.html
* http://edusagar.com/articles/view/22/Uni...-internals
* http://www.cs.pomona.edu/~markk/filesystems/bsd.html
* https://en.wikipedia.org/wiki/Ext2
* http://e2fsprogs.sourceforge.net/ext2intro.html
* http://teaching.csse.uwa.edu.au/units/CI...2fs_1.html
* http://xpt.sourceforge.net/techdocs/nix/...01s06.html
* http://perl.plover.com/yak/ext2fs/
* https://en.wikipedia.org/wiki/Log-struct...stem_(BSD)
* https://en.wikipedia.org/wiki/Procfs
* http://www.tldp.org/LDP/intro-linux/html...03_01.html
* https://en.wikipedia.org/wiki/List_of_file_systems
* http://www.shub-internet.org/brad/FreeBSD/postmark.html
* https://en.wikipedia.org/wiki/Disk_sector
* https://en.wikipedia.org/wiki/Hard_disk_...#Seek_time
* https://en.wikipedia.org/wiki/Block_suballocation
* https://en.wikipedia.org/wiki/Inode_pointer_structure
* https://en.wikipedia.org/wiki/Inode
* https://dlorch.github.io/hammer-linux/fi...-lorch.pdf
* http://www.osdevcon.org/2009/slides/zfs_..._graef.pdf
* https://en.wikipedia.org/wiki/ReiserFS
* https://en.wikipedia.org/wiki/HAMMER
* https://www.dragonflybsd.org/hammer/
* https://www.princeton.edu/~unix/Solaris/...t/zfs.html
* https://en.wikipedia.org/wiki/QNX4FS
* https://en.wikipedia.org/wiki/XFS
* https://en.wikipedia.org/wiki/ZFS
* scsitools-gui
* Installation: https://docs.freebsd.org/doc/7.4-RELEASE...disks.html
* http://www.tutorialspoint.com/unix/pdf/u...system.pdf
* https://en.wikipedia.org/wiki/PhotoRec
* https://en.wikipedia.org/wiki/GNU_Parted
* http://freecode.com/projects/fstransform
* http://www.cis.upenn.edu/~bcpierce/unison/
* https://en.wikipedia.org/wiki/Unix_File_System
* http://pages.cs.wisc.edu/~remzi/OSTEP/fi...tation.pdf
* http://www.scylladb.com/2017/10/05/io-ac...ds-scylla/
* https://www.nextplatform.com/2017/09/11/...-posix-io/
* http://www.campus64.com/digital_learning...alysis.pdf
* https://opensource.com/article/18/4/ext4-filesystem


If you want to contribute check this thread.

Music:
Mosquito by Pk jazz Collective http://store.southerncitylab.net/track/mosquito
venam
Transcript:
# Data Storage on Unix & Filesystems #


### Table of content ###

* Intro
* Ideas and concepts
* The overall generic architecture
* Lowest level - Hardware & limitation
+ The medium
+ Connectors
+ The Drivers
+ A mention on block devices and the block layer
* Mid level - Partitions and volumes organisation
+ What's a partitions
* High Level
* A big overview of FS
+ FS Examples
+ NB about 32 bit limitation
+ A bit about history and the origin of Unix FS
+ VFS & POSIX I/O layer
* POSIX I/O
* MANAGEMENT, COMMANDS, & FORENSIC
* Conclusion
* References

-----

# Intro #


Libraries and banks, amongst other institutions, used to have a filing
system, some still have them. They had drawers, holders, and many tools
to store the paperwork and organise it so that they could easily retrieve,
through some documented process, at a later stage whatever they needed.

That's where the name filesystem in the computer world emerges from and
this is one of the subject of this episode.

We're going to discuss data storage on Unix with some discussion about
filesystem and an emphasis on storage device.


# Ideas and concepts #


What's data storage and what's a file system?

Data storage is whatever mean that is used to store information on
a medium that can contain that body of data and that offers a way to
search for that information back.

The data storage medium we'll focus on will be the long term physical
storage devices, like hard disks, and not the virtual ones that only
exist in memory or networked ones.

A file system is a way to give meaning to the placement of this
information instead of having it as a big blobs of 1s and 0s. A file
system helps by offering an interface to isolate, group, classify,
delimit, to know where the information starts and ends, give pieces of
information an identifier, a name, give the information different sort
of attributes like access rights and metadata, etc..

There are many different kinds of file systems that can be used on
different types of storage devices, each one with different specificities
and ways of handling information.

So, we've delt with definitions, now let's talk about the big architecture
of all the components that are involved.


# The overall generic architecture #


To better understand the architecture of the data storage you have to
think about it as a sort of two way street which has two roles, to read
or to write. Along the way the data travels that street and stops at
those components that are in the middle parts of the architecture.

Those components sometime keep a log of whatever passed through them,
they cache it so that they can cast away the request, pushing it back
to where it came from.

You can also think about it like everyone of those nodes have both a
read and write methods and apply those methods to one another, though
it is not always as simple as that but it gives a picture of the flow.

Let's go through the layers quickly so that we can grasp the overall
architecture.

At the lowest of layers we have the physical device itself, be it an
HDD or SSD or DVD or SD or Flash, etc..

Those devices have a connector that speaks a certain transfer protocol,
which is usually a SCSI or ATA cable.

Above this we have the drivers that maps and interacts with those devices
via the connectors, not only to transfer data but also to configure and
read metadata from them.

On some systems, the driver interacts with the BIOS (basic input/output
system) instead of interacting with the connector directly. However,
on most Unix this is not the case, the driver speaks directly with
the connector.

Above the drivers we have an optional block layer that buffers, schedules,
and queues requests that will be sent to the device. It also uses the
block as a unit independently of what the real unit of the device is. For
example, on a hard disk the sector size is usually 512 bytes while a
block could be 4096 bytes (this is related to the filesystem).

The next layer on top is optional and is composed of hardware abstraction
such as hardware encryption, disk spanning via LVM - logical volume
management or the MD driver on Linux, RAID for redundancy, etc..

Above this we have other abstraction layers that consist of the VFS,
the virtual file system, and the page cache that could possibly be paged
out to the physical device or used to cache some of the disk I/O.

The virtual file system is an abstraction layer that interfaces between
the user and the file system in use, its role is to give the same
interface whatever the file system in use. So the filesystem is sort of
within this layer too.

More precisely "The VFS provides the abstraction layer, separating the
POSIX API from the details of how a particular file system implements
that behavior."

As you can see, those are blocks fitting into one another. Keep them in
mind all along as we're going to dive into everyone of them one by one.


# Lowest level - Hardware & limitation #


## The medium ##


Let's talk about the hardware.

The lowest/minimal unit of storage on a medium is the sector. A sector
is a block/cell of bytes of a certain size.

Some devices have physical hardware sectors like hdd and ssd but others
have it abstracted by the software and have no physical delimiters.

This makes the storage medium a grid of cells that can be used to
store data.

Those sectors are addressable, that means they can be pointed and found
by reading and writing at their specific offset, this makes searching
and writing information more efficient.

A lot of the logic, abstractions, and file placement optimization done
at higher levels (optimizing seek time for example) are and were made
with the assumption that we are interacting with a hard disk. So it's
important to know the physical layout of a disk.

A disk is composed of stacked platters that spin/rotate while a head
assembly/actuator reads from one side of a platter at a time. The platter
has two faces, each face is called a head.

The platter itself is divided in concentric circles that are called tracks
or cylinders, the difference doesn't really matter here. Those tracks are
also divided into smaller parts that are all the same size called sectors.

This is the sector that we've talked about when it's applied to the hard
disk case.

If you know the right head, the right track, and the right sector then
you can pinpoint the data you want. However most of today's hard disk
have this abstracted and map sectors globally, so you can point directly
to a general address without having to know about the rest. Which is
also nifty because it can apply to other devices with sectors like SSD
or optical disks, not only hdd.

This is called LBA, Logical Block Addressing which is in contrast with
CHS, cylinder-head-sector addressing. LBA addresses can be translated
back and forth to CHS.

So when data is stored on the hard disk it's usually stored on a bunch
of sectors and whatever space is left on the sector is left as is,
though some filesystem may optimize that space (but usually optimize
blocks and not sectors).

Because data is stored on sectors and sectors are physical parts of a
disk that can have physical space between them, it takes time for the
head assembly/actuator piece to travel from one sector to another. The
average time it takes is called the seek time.

This time is quite big in computer time, from 5 to 10ms, it's very slow.

As we've said some the optimizations done at higher level do take this
time in consideration and try to minimize it. Placement of files and
caching comes to mind.

SSD eliminates motor movement and rotation and so is faster and doesn't
have the same issues as with HDD and other medium.

> With SSDs there are no moving parts, so a measurement of the seek time
> is only testing electronic circuits preparing a particular location on
> the memory in the storage device. Typical SSDs will have a seek time
> between 0.08 and 0.16 ms.

In sum, this is the layout of a hard disk and what it implies.

It's also nice to know that most physical medium have a hardware way to
checksum, check the integrity and health of its own data.

This is done through error-correcting code and bits.

HDD, SSD, optical disks, etc.. all have those.

The command that can show the physical sector size is the `fdisk -l`.

Now we can move to the connectors, the interface with the physical medium.


## Connectors ##


Let's focus on what those connectors are and what they do.

When I say connector, I mean the low level commands to interact with
the disk or other device - the hardware interface.

There are 3 different components or ideas that are the most important
here, the SCSI interface, the ATA interface, and the BIOS interface.

All of those are standards that could be implemented as ways of speaking
with the data storage, to make it do something useful and even configure
it in some cases.

The SCSI and ATA interfaces are to interact with the device directly,
we call those "direct access to controller", while the BIOS, Basic
Input Output System, access to controller can be used as a middle man
to translate the communication with the actual device - Which as you
would guess is a bit slower but more convenient than the direct access.

On most Unix-like systems, the communication is done directly and doesn't
use the BIOS, which means SCSI and ATA are the main way of interacting
with the storage devices and that there are specific drivers understanding
how to do that.

Let's note here that most direct access devices are equipped with read
and/or write caches parameters. Remember that.

Wait, We know what's a BIOS but what the hek are SCSI and ATA?

SCSI, skuzee or sexy (as the original creator hoped it would be pronounced
as), stands for Small Computer System Interface, it's a set of "standards
for physically connecting and transferring data between computers and
peripheral devices".

The standard defines a protocol and commands to interface and control
those peripheral devices.

Note here that we said peripheral devices and so this standard is
not limited to any specific data storage device, or data storage in
general. Though it's commonly used for hard disk drives and tape drives,
it can be used for CD drives and scanners or anything else.

Simply said, it's just a standard way of communication so that different
devices can communicate with each others.

There are versions of the standards with different speed increase
over time.

Physically, the connector is the cable and the cable of the SCSI standards
have a distinct set of pins to send the data over.

What about ATA?

ATA stands for "AT Bus Attachment" or simply "AT attachment".

The name originates from a standard first implemented in the IBM PC/AT,
where AT stands for "Advanced Technology". Now it's just kept as AT
Attachment to avoid trademark issues with IBM.

ATA has a long history of a series of iterative and incremental
updates. It was first a response to SCSI's flaws.

It has a different connector/cable type, is cheaper, is faster, and has
more features, in theory.

One of the feature is the LBA which comes by default since v0 of the
ATA. This LBA, logical block addressing, which we talked about earlier,
is the physical address method that uses a single number instead of the
cylinder-head-sector method.

LBA became the new standard with backward compatibility to convert back
and forth.

IDE, one of those version iteration names is sometimes mixed up with ATA.
In fact other names too get mixed up with it, like ATAPI, UATA, IDE,
etc.. Because in fact they are near synonyms, they are refering to the
same thing.

What's special about IDE disk, integrated disk electronics, is that they
have a logic board built into it. Actually ATA disks require a controller
which is built into the disk of modern systems. The controller issues
commands to the ATA disks over the ribbon cable, the channel.

IDE is not just the connector and interface, but it's the fact that
you need a drive controller integrated into the drive as opposed to a
separate controller on or connected to the motherboard - like with SCSI.

The interface that an IDE uses is the ATA interface.

This means that ATA is limited to hard disk usage unlike SCSI which has
a controller in the motherboard so can be used with everything.

The ATA interface is the most popular disk interface these days, it's
used everywhere.

Because it's built into the disk ATA offers custom commands like hard
disk password, the manipulation of disk specific parameters such as host
protected area, the max address, the device configuration overlay, etc..


At some point ATA and SCSI started to bottleneck, they were getting slow.

Starting from the ATA-7 specification in 2003 something called serial
ATA, or SATA for short was introduced, at the same time the original
ATA was renamed parallel ATA or PATA for short.

The same happened with SCSI, with the serial attached SCSI or SAS
for short.

Both of those offered many advantages while still being compatible with
their specific older interface.

Reduced cable size, faster speed, reliability, among others.

SATA is the defacto today for consumer devices such as desktop and
laptops, 99% of the market share as reported in 2008.

So both ATA-like and SCSI-like interfaces sound very similar, they both
more or less do the same job, have direct memory access, feature command
queuing, have swappable connectors to allow to hot-plug the drives when
the system is on, have self-monitoring and analysis features such as
SMART, etc..

Now the question is: Can they work together, are they compatible?

And the answer is yes.

At first when ATA appeared they were cheaper but SCSI were already on
the market so the compromise was to implement in ATA the ATAPI, ATA
packet interface which would allow ATA devices to speak SCSI.

Then ATA got more popular than SCSI and so SCSI devices implemented
the ATA command pass-through feature, or serial ATA tunneling protocol,
which allowed ATA commands over SCSI bus.

SAS even used the same connection as SATA which allows a SATA drive to
be connected on a SAS backplanes/controllers, but not the reverse.

And then they finally put a standard in place for translation both way,
this standard is called the SCSI/ATA Translation (SAT).

So you can send ATA commands to SCSI devices such as CD-roms via the
ATAPI interface or SAT. Actually in practice ATAPI is only used for
devices other than hard disks.

So ok, that was a long overview of the hard disk world.

Now how do we access those on Unix, are there commands to configure,
set the hardward cache, etc.. and get info about those drives.

A warning beforehand, you might crash your computer, loose data, or
not easily be able to recover if you execute some of those commands
improperly.

So, here are some:

* `fdisk` to manipulate disks and show information about them
* `hdparm -I /dev/sda` to show and configure ATA
* `scsiinfo -l` same for SCSI devices
* `scsitools` bunch of tools for analysing and exploring scsi and ata
* `camcontrol` The FreeBSD utility to manipulate driver of devices
* `atacontrol` Also FreeBSD utility to control ATA devices
* `smartctl` to manipulate ATA devices that have the SMART feature
* `vpddecode`
* `dmidecode`
* `biosdecode`
* etc..


## The Drivers ##


So those were the physical parts, and like most physical parts they need
drivers so that the operating system can map/mount them and interact
with them.

How is it done on Linux and the BSDs?

The big difference lies in the stuffs we've learned about just now,
the SCSI and ATA.


On Linux there are two drivers, a deprecated one the traditional ide
driver which is used for many common SATA chipsets, and libata, the
newer ATA driver.

You can also optionally load (other than the driver for IDE) at the
software level support for BIOS interface we discussed earlier in
case it provides some specific manufacturer software such as RAID
(fakeraid/ataraid/dmraid).

What's particular about libata is that it provides a SAT (SCSI/SATA
Translation) implementation, it sits inside the kernel well-tested SCSI
layer on Linux.

Each SATA port on Linux will apear as a SCSI bus.

Ok, so what does that mean?

There's a mid-level, that is the SCSI layer common to a bunch of other
lower operations that are translated to other SCSI-like services.

This layer, if built as a module would never need to be loaded as any
lower module would depend on it and load it. So usually it's always
loaded and not a module.

Which means that those data storage device all use the SCSI
layer? Yes. And that means that if they want to use more specific
configurations they'll have to bypass it to interact directly with the
device? More or less yes.

That also means that it affects the mapping of SCSI and ATA devices
under /dev.

Remember that a device is a gateway to a driver in the kernel that
controls the device and not the actual device itself.

So the SCSI and ATA disks are both mapped as `/dev/sd*` devices. `sd`
standing for SCSI device.

`/dev/sda` for the first disk, `/dev/sdb` for the second, `/dev/sdc`
for the third disk, etc..

And if we take a look under `/proc/devices` we can find out that those
are block devices (we'll explain what that means later) with major
numbers 8 and 65 through 71, etc..

`/dev/hd` is used for the IDE subsystem.

`/dev/sr` for cdrom subsystem (iso9660).

There are more precise things in the devfs subsystem `/dev/scsi` and
you can get more details about the SCSIs by checking `/proc/scsi`.


That's enough about Linux, now what about BSDs?

Every BSD has a different way of implementing the drivers, and different
names but one thing in common is that there's a separation of drivers and
mapping, that means a clear separation between ATA and SCSI and not a SAT
(SCSI/ATA Translation implementation).

We'll take FreeBSD as an example.

The drivers that are interesting for us are the ad and da driver, the
ATA disk driver and the SCSI direct access driver.

Apart from those you have the ar driver for ATA RAID, the acd driver for
the ATAPI for cd or just cd for SCSI cdrom, the afd ATAPI for floppy,
the ast ATAPI for tape drive.

You can clearly see that the drivers don't have a generic middle layer
like Linux but very separate ones.

So all IDE/SATA drives shows as `/dev/ad*` and all the SCSI drives and
USB mass storage as `/dev/da*`.

Another difference is that on FreeBSD block devices have been dropped
so all those devices are character devices.


### A mention on block devices and the block layer ###


What are block devices, what's the block layer, and why would FreeBSD
drop it?

The idea behind all those is that if there are a lot of requests to the
data device then it might not be able to handle the throughput and so a
queue/buffer/cache layer may need to be inserted in the middle so that
it is read before or written to before the real device.

This is the block layer that is found in the kernel and every block
device has a buffer in the block layer. This is what a block device is.

All block devices are viewed as a linear collection of blocks of the same
size, those blocks are the size of the cache entry, which is usually
the same as a filesystem block as we'll see later, but is a different
cache than the filesystem cache.

This layer has some queuing and scheduling put in place too.

However there are a lot of criticism about it.

1. Some ATA devices already provide built-in hardware caching mechanism.
2. Like all caches it's stored in the kernel and add complexity to it.
3. It may be unreliable as the kernel has to maintain efficiently the
cache sometime reordering the requests, and also has to do some
frequent housekeeping of the data structure.
4. In case of crash the data might be lost and unrecoverable.

For all those reasons FreeBSD and others dropped support for cached/block
disk devices.

The relevant command is: `blockdev --getbsz /dev/sda` to find out the
block size.

I haven't found a way to flush the blocks directly on Linux because it's
mixed up with the page cache too.

You can flush the filesystem page cache using `sync` but this is different
than the block buffer, however both page cache and buffers starting from
Linux 2.4 are joined (somehow, we'll discuss page cache later on).

You have to do `sync; echo 3 > /proc/sys/vm/drop_caches` to drop them.

Yes this is a bit confusing.

So, we mentioned the way devices are mapped in `/dev` however there's
the appended digits and characters we haven't discussed, what are those.

Let's talk about partitions and volumes.


# Mid level - Partitions and volumes organisation #


We mentioned partitions so let's explain what those are and with those
we can also insert the layers related to RAID, volumes, and encryption,
as you'll see those fit together in the same basket.


A partition is a way to slice/shred up a disk into multiple sections
with different roles.

There are many reasons for that, for example the separation of data or
having multiple operating systems on the same disk.

It's practical because on Unix you can have separate partitions for
different directories and those partitions don't have to be mounted on
the same disk.

But what's the difference between a partition and a volume, those terms
sound similar and you might have heard of them in the same context
however they shouldn't be mixed.

A volume is a group of addressable sectors used for storage, addressable
in the sense that they can be pointed to, thanks Mr.obvious. However,
that means those sectors don't have to be consecutive nor on the same
disk. The operating system will see them as one big block, a volume.

A volume can be a single disk, or many smaller disks into one, this is
called disk spanning.

A partition on the other hand is a collection of consecutive sectors in
a volume. Now the limitation is that they live inside a volume and that
the sectors are consecutive.

The partition can be virtual if inside one of those volume or it can
be physical if directly on the disk. A physical partition can contain
a volume which can contain logical partitions.

Usually there can only be 4 main partitions on a disk, and a special
partition called an extended partition should be used to have more.

Check the podcast about booting on Unix for more info on that subject.

To sum it up a volume is what the OS considers as a bunch of addressable
storage space, this can be many disks or a single disk, and a partition
are the separate consecutive sectors that are part of those volumes or
the physical disk.

You can have 3 partitions in one volume and that volume spanning over
2 disks.

Usually a volume is synonym with one disk as setting up the other options
is more tedious, we'll discuss the implementation in a bit

Now how does the addressing works here?
There are many layers, remember when we mentioned the CHS
(cylinder-head-sector) way and the LBA (logical block address), now
you have to add to those the layer on top for the volume which is the
logical disk volume address, which basically starts at 0 for the start
of the sector of the volume and ends with it, remember that it doesn't
have to be the start of the disk.

Other than that you have to add the same thing for the logical partition,
a way to point to sectors inside of it, thus there is the logical volume
partition address.

That's a lot of blocks stacking up.

As we said normally the volume is the physical disk itself but to have
the spanning over multiple disks or chunks of disks you have to have a
software implementation or a hardware one.

This could consist of a specific volume management driver or of RAID.

Let's discuss some software implementations.

On Linux for instance, to make those all work, it uses a layer called
the device mapper, a framework provided by the kernel to map physical
block devices into virtual block devices that can be used by those
"volume-like" modules.

It's a transition module in the middle of the block layer and the
volume-handling layer.

It can also be used for disk encryption (dm-crypt).

This device mapper behavior is also present in some BSDs such as NetBSD
and DragonFly BSD.

On Linux there are two implementations of the volume management, LVM
(logical volume management) and MD.

LVM calls the volume a disk group or volume group,

Disks in the volume group are divided into physical extents, equal
size containers.

A logical volume is made up of logical extents, and there is a mapping
between each logical extent and the physical extent.

What about RAID, the redundant array of inexpensive disk.

We consider it in the same category as volume handling as it manages
multiple disks, sometimes as one, sometimes as replication, sometimes
as error correcting.

RAID 0 is like disk spanning of volumes, it spreads the data over multiple
disks in chunks.

* RAID 1 is pure mirroring.
* RAID 2 adds some error correcting codes.
* RAID 3 adds a disks that calculates the parity of the last bytes.
* RAID 4 is like RAID level 3 but using block sized chunks.
* RAID 5 does the same as RAID 3 but alternating the parity check from
one disk to another.

The mapping of the devices in `/dev` changes according to what we've
discussed, apart from the SCSI and SATA we mentioned earlier.

It adds volumes and partitions to the mix.

On Linux partitions are represented by additional numbers added.

For example, the first SCSI disk is `/dev/sda` and the first partition
on it `/dev/sda1`, second partition `/dev/sda2`.

That is regardless if it's a partition on an an extended partition like
GPT or one of the 4 main partitions.

On FreeBSD it's a bit similar.

However the naming differs, the 4 main primary partitions are called
"slices", then has logical "partitions" inside the slice.

The drive number is also, like on Linux, define by adding a digit at the
end of the device name (instead of a letter): `/dev/ad0` is the first
SATA drive, `/dev/ad1` the second, etc..

The slices (4 primary partitions) are defined by adding an "s1", "s2",
"s3", "s4" after the drive in question.

So for instance for the first slice of the first SATA disk you would have
`/dev/ad0s1` and for the second slice `/dev/ad0s2`.

As for the partitions inside the slice, it's done by adding a letter:
`/dev/ad0s1a`, `/dev/ad0s1b`.

Usually on FreeBSD those partitions are standardly mounted on specific
directories, such as "a" being `/`, "b" being the swap, "c" overlaps
all the other partitions on the disk, "d" covers the whole disk entirely.

What does mounting mean?

On Unix everything is represented under a root directory, even the disks
themselves and so you need to have a sort of access point that says this
directory points to this devices.

In simple terms that's what a mount point is.

For example you mount `/dev/sda3` as an ext2 filesystem on the mount point
`/tmp` and whenever you write data to `/tmp` it'll be on `/dev/sda3`.

There are many ways to mount a device, you can use `fstab`, you can
manually mount the partition, you can dynamically mount it, etc.. But
I won't go into more details.

How does the OS know where to find them?


## What's a partitions ##


A partition is defined inside the parent volume/disk partition table,
be it a DOS/MBR partition or a GPT (extended) partition (check the
podcast about booting for more details, or just read up online).

It's a fixed size structure that contains metadata about what's in there,
it can say "here is an LVM partition" or "here is some boot code" or
"here is an ext4 filesystem".

One of the entry in that structure does just that, it's the partition
type a Byte specifying the partition ID, which is the type of filesystem
or object present on this partition.

For example:
```
0x83 - linux
0x85 - linux extended
0x8e - LVM
0xa5 - freebsd
0xa6 - openbsd
0xa8 - max osx
oxa9 - netbsd
0xee - efi gpt partition
0xef - efi system partition
```

There's a list in the show note (`partition_type`).

Other parts of the structure are the size of the partition, where it
starts and where it ends.

But what's actually inside the partition we are mounting?

Usually there's the filesystem.

In the first few sectors of the partition the filesystem stores its
metadata, its label, its paging area, the file system structure, the
control block with ownership and data location, the free space mapping,
and a lot of specific filesystem components.

Here are a bunch of useful commands:


```
~ > sudo blkid
/dev/sda1: PARTLABEL="BIOS boot partition" PARTUUID="093c568a-be66-4475-99b6-a70dc67f635d"
/dev/sda2: UUID="78b19097-1d52-4c9f-b076-813bfff87118" TYPE="ext4" PARTLABEL="Linux filesystem" PARTUUID="5e2787ff-023d-4768-aeda-c268b5909c5b"
```

```
~ > lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 465.8G 0 disk
├─sda1 8:1 0 1M 0 part
└─sda2 8:2 0 465.8G 0 part /
sr0 11:0 1 1024M 0 rom
```

```
~ > sudo fdisk -l
Disk /dev/sda: 465.8 GiB, 500107862016 bytes, 976773168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: 58570BC8-A049-4505-BC69-74B186F748C2

Device Start End Sectors Size Type
/dev/sda1 2048 4095 2048 1M BIOS boot
/dev/sda2 4096 976773134 976769039 465.8G Linux filesystem
```

```
~ > lsmod | grep ata
Module Size Used by
libata 208896 2 ahci,libahci
scsi_mod 155648 3 sd_mod,libata,sr_mod
```

Ok, now what exactly is a filesystem, what does it do, what's particular
about it, how can it be implemented, and what are all those metadata for.


# High Level #


# A big overview of FS #


As we said the partitions are defined by their type, one of those type
is the file system type.

The partition, the isolated storage segment, is loaded and interpreted
as a filesystem.

A file system is the bulk of this episode, without it nothing makes
sense, without it it would be data scattered around with no specific
meaning attached to it.

The file system is the way the OS store, update, and retrieve the data.

Ah that sounds repetitive, we've already said that it seems.

But this time it stores the data in a hierarchy of files and directories.

It's the file system that create the structure around files and use data
so that the OS knows where to find them and what they represent.

It's a "structured data representations and a set of metadata describing
the stored data".


We gave the metaphor in the introduction of this podcast about the filing
system that some banks have, well this is the job of the file system.

It keeps track of what is what, their name, where they are, who has
access to them, it organises them, keeps the office tidy, etc..

And when you ask it where something is then it has a procedure in place
to be able to find it as fast as possible.

To do all that the file system needs an internal data structure and
organization: The metadata and caching.

It has two structures in place, one in memory and one on disk, a temporary
and permanent one.

Let's talk generically and then discuss the differences between
implementation of file systems in the Unix world.

First of all, the layer just under the file system is the block layer,
or whatever replaces it, thus the file system operates on blocks and
not on sectors. Those blocks range from 1 to 128 sectors (512B-64KB).

The file system stores files on those blocks, usually at the start of
the block and taking it entirely, even if the file doesn't fill it all.

(Just like sectors space is wasted)

There are some exception to this where the file system optimizes that
wasted space, this is called block suballocation. And the wasted space
phenomena is called internal fragmentation.

The last few things I mentioned mean two things, that the file system
should keep track of which block is used and unused and to keep track
of what is on which blocks.

Both those information are stored in what we call the superblock or
volume descriptor.

It contains all the important metadata required to use this file system,
its type, size, status, and more importantly information about where
other metadata structures are such as the free space mapping structure,
and the structure that represents the files used on which blocks.

Without the superblock the file system is useless, it cannot be mounted
and cannot be used.

Those are the permanent structures.

The tracking of free space could be simply implemented as a
bitmap/bit-vector, every bit position representing the position of the
block in the block data of the filesystem. Or it could be a linked list,
or anything, this depends on the implementation.

The second structure is the inode table, a table containing all the
inodes.

The inodes or vnode or other kind of similar implementations names
is a structure that has a number (an id) and other data that can help
pinpointing the files on the disk and letting the OS access the files.

It contains things such as the file size, the device id of the device
containing the file, some permission related metadata, some timestamp
metadata, a count of the number of hard links pointing to that file,
and more importantly here: "Pointers to the disk blocks that store the
file's contents", the inode pointer structure.

There are usually two inode numbers that are recurrent on most Unix
systems, inode 1 is used as a "bad blocks inode", and inode 2 is used
as the root directory inode.

For example on Linux `/sys` and `/proc` which are not on the disk have
the inode 1.

One thing to note is that if the file system runs out of inodes then it
is considered full, even though the disk might not be.

A block in itself could be smaller than the file size, that means a file
will own multiple blocks to store its content. In its inode it has a
list of pointers to the disk blocks.

But when a file is created how do we choose which blocks to give to a
file, how do we do space management.

Well, obviously this is file system dependent.

Common ways to allocate the blocks are the first block found, or the last
block found, or the best fit, or the worst fit. You can mix those around.

Usually the worst first fit is the best algorithm as it reduces the
amount of external fragmentation.

Fragmentation is when unused space or single files are not contiguous
on the disk, the file blocks are scattered around.

This happen when a program allocates blocks and then frees blocks in
the middle and then the memory allocator uses this free block to store
the data but the data doesn't fit in one block and thus it's allocated
to another block further away. Another case when it happens is when
a file grows in size and doesn't fit in the space allocated already,
it has to allocate a new block that isn't contiguous.

With Unix file system fragmentation isn't that big of an issue but with
other file systems it might as the head/actuator will be moving around
the disk too much and slowing reading speed.

On Unix disk reads are cached, and even has read-ahead, which buffers
the next block intelligently. Moreover the position of the disk head is
irrelevant as Unix is a multi-tasking OS and multiple users will already
be reading all over the disk.

Overall disk fragmentation is a sign of a bad implementation of block
allocation.

Ok, so that's how allocating blocks work but how can it be stored, all
those related blocks together in the inode or whatever structure used
to store the file information.

It could be a contiguous preallocated array of blocks, it could be a
linked list of pointers to next blocks, etc..

Most Unix file system use a combination of direct and indirect block
pointers, for example allocated in this fashion: Allowing 12 direct
block pointers and 3 indirect block pointers, single, double, triple.

A direct block pointer is a pointer to a block that the file has data
into, an indirect one is a pointer that points to another direct or
indirect block pointer.

The combination of those means that the file can grow as it needs.

"""
In the past, the structure may have consisted of eleven or thirteen
pointers, but most modern file systems use fifteen pointers. These
pointers consist of (assuming 15 pointers in the inode):

Twelve pointers that directly point to blocks of the file's data
(direct pointers)

One singly indirect pointer (a pointer that points to a block of pointers
that then point to blocks of the file's data)

One doubly indirect pointer (a pointer that points to a block of pointers
that point to other blocks of pointers that then point to blocks of the
file's data)

One triply indirect pointer (a pointer that points to a block of pointers
that point to other blocks of pointers that point to other blocks of
pointers that then point to blocks of the file's data)
"""

What about the in-memory structures we mentioned.

The kernel keeps a global file table, it keeps track of the byte offset
where the user's next read/write will start, the access rights, etc..

The in-memory structures can also have a process file descriptor table
keeping track, in every process, of the files taht are currently opened.

It also has a page cache, a copy or partial copy of file content,
sometimes at the virtual file system level.

In some cases it unifies it with the buffer cache into a two page cache,
both the hard disk page size and file system block size.

The difference is that buffers (block layer) are associated with a
specific block device and its metadata while the page cache contains
parked file data.

"That is, the buffers remember what's in directories, what file permissions
are, and keep track of what memory is being written from or read to for
a particular block device. The cache only contains the contents of the
files themselves."

Buffer = Metadata; Cache = Data;

The page cache caches pages of files to optimize file I/O. The buffer
cache caches disk blocks to optimize block I/O.

This is confusing as the block layer caches writes to disk, the page
cache caches pages of files, and the buffer caches blocks and metadata
about the filesystem.

It has confused me too and I'm not sure the differences are clear here.

The memory structure can also have cached directory information, which
is very important, the dentry.


## FS Examples ##


What can differ from one file system to another.

The block size, the caching algorithm, the
block-allocation/space-management algorithm, how it stores the metadata
about files and what's in that metadata, the speed at which the data is
fetch, if it has some specific features.

Bigger block size will mean improve disk I/O performance when using large
files but when using small files it will result in a lot of wasted space
if suballocation is not used.

For example as of 2015 (wikipedia), block suballocation is most widely
used with Btrfs and FreeBSD UFS2.

Another example, Ext2 space management algorithm tries to find 8 free
data blocks before allocating and doesn't allow two files to allocate
at the same time.

An interesting allocation is the data block deduplication, which will
consider identical block as the same block and not reallocate it.

The HAMMER file system implements this.

A file system can have some extra integrity mechanisms, if the power
is cut before the data is written to disk or if there's a media failure
there should be a way to recover.

Some file systems offer some damage correction, fault-tolerance,
structures and features such as checksums, recovery, rollbacks and
journaling.

The Ext2 file system, for instance, has integrity check.

Ext3 has journaling and ReiserFS too.

Journaling meaning that the file system maintains a journal/log of what
is currently happening on the file system, thus can traceback events in
case of crash.

Some file systems have some limitations in size, what it allows in its
filenames, etc..

Some file systems have a snapshot feature, allowing to backup and rollback.

For example ZFS, HAMMER fs, and Btrfs implement this snapshot feature.

Some file systems allow pooling, sub-filesystem or sub-volume managed by
the file system itself, yet another splitting. Though it could be said
that it's and implementation of a file system and a volume manager in
the same software.

ZFS and Btrfs also have those.

There are file systems optimized for specific devices and usages.

For example there are file systems optimized for flash memory, solid
state media, for CDROM and optical discs, others for distributed systems,
others for network, others for encryption, etc..


Some commands that can be interesting here are the `mkfs` and `newfs`
and fsck for checking a file system integrity.

There's also GNU parted that can be used to create file system.


### NB about 32 bit limitation ###


It's common parlance that on 32 bit operating system file systems have
a certain limitation for their file size.

This is actually not a limitation from the file system, not from POSIX,
but rather indirectly from ISO/ANSI C.

If you've listened to the podcast about bits and words then you would
guess what the issue is.

"The `lseek()` file offset is defined as `off_t`, there's nothing in a
32-bit POSIX compliant system to stops it to typedef'in it as a 64-bit
signed "long long", same for a bunch of function like `fsetpos` and
`fgetpos`, however the problem lies with ISO/ANSI C `fseek` and `ftell`
functions which use a "long" for the offset instead of `fpos_t`. This
limits the size of a file to 2GB."

"Thus, it is ISO/ANSI C compatibility that is necessarily broken for file
systems that support bigger-than-2GB files with 32-bit longs -- something
that applies even to non-POSIX file systems that claim compatibility
with ISO/ANSI C. I'm sure you all can think of at least two, but that's
a discussion for the advocacy lists."


## A bit about history and the origin of Unix FS ##


The original ideas about file systems haven't changed much since the
early days.

The first Unix file systems were referred to as FS, they had boot block,
superblock, a clump of inodes, and the data blocks.

Which we also have today, however today we have much more efficient
structures.

The ideas weren't all new, as with everything UNIX, it was inspired
by MULTICS and other operating systems that had those kind of similar
structures. What was new was the simplicity over functionality.

This simple file system was improved later by the BSD guys to reduced the
disk head/actuator movements, it broke the disk into smaller chunks/groups
and each having its own inodes and data blocks. The cylinder clusters
and bit-map free lists.

Till today most file systems have similar commonalities such as dividing
the disk in blocks, using inodes for files, have a directory structure,
use the first block of each volume for bootstrap, use an inode table,
have a superblock aka volume descriptor, a block pointer scheme, etc..

There's not much to say about the original history of file systems,
however there's one part that is important for the next topic: Having
different types of file systems together.


## VFS & POSIX I/O layer ##


The virtual file system is an abstraction layer that interfaces between
the user and the file system in use, its role is to give the same
interface whatever the file system in use. So the file system is within
this layer.

More precisely "The VFS provides the abstraction layer, separating the
POSIX API from the details of how a particular file system implements
that behavior."

This means Unix-like OS that have this kind of interface support different
type of file systems.

Generically those are layers that allow an operating system to access
a file system via a common interface, a file system interface.

This is called the common file model.

There are many implementations such as FUSE, LUFS, VFS, which is the
most used name for it on Unix-like systems (even though they might not
be the same).

Where does the concept of VFS come from?

Virtual file system mechanism on Unix-like system was introduced by Sun
microsystems in SunOS 2.0 in 1985.

Sun introduced a way to access the local UFS file system and the remote
NFS transparently from the same usual system calls.

Other vendors that were implementing the NFS of Sun had to also implement
this layer.

Other file systems could also be plugged in this layer to add support
for them, for instance MS-DOS FAT was developed for SunOS.

Soon enough this lead to widespread implementation of the same mechanism,
the SunOS implementation was the basis of the VFS mechanism in System V
Release 4 and later implemented in 4.4BSD and derivatives.

In 1993, the ext2 file system was added to Linux instead of the MINIX-like
implementation to allow support for different kind of file systems.

But how does the VFS work, how does it know which file system is present.

It all has to do with superblocks, it reads it, knows what kind of file
system it's dealing with, and map it to its internal memory structure
of VFS superblocks.

The real file system stays as a driver or built-in the kernel.

Thus, every mounted file system is represented by a VFS superblock,
which contains the following and more:

The device that contains that file system, the partition, etc..

The file system type it is.

Inode pointers, those point to the first inode in the file system and
the inode of the directory it's currently mounted on.

The block size of this file system.

The superblock operation, a translation table/map (operations vector)
of routines used to interact with the file system.

The VFS also has its own inodes, the VFS inodes which are built from
information of the underlying file system inodes.

The system processes accessing files and directories do it through
this layer.

And if those inodes are accessed repeatedly they are kept in the inode
cache of the VFS for quick access so that it doesn't have to be fetched
again.

This is yet another layer of cache other than the built-in one in the disk
and the block buffer layer (or whatever abstracts is like map-device).

Now you can say that here it's the VFS that inserts data in the
buffer/block layer.

The VFS also keeps a cache of directory lookups so that the inodes for
frequently used directories can quickly be found, the dentries cache.

As the name implies, the VFS is virtual and so those structures and
caches are kept in memory and not permanently.


So this is the VFS from the side of the file system, what does it look
like from the side of the user?

In short, it provides the basic POSIX file I/O functions.

When a system call is issued it passes through the common interface
provided by the VFS, is mapped via the VFS superblock and interpreted,
buffered through the block layer if any and then goes down the pipeline.

There are many system call supported by the VFS such as:

```
–Mount(), umount()
–Chroot()
–Chdir(), fchdir(), getcwd()
–Mkdir(), rmdir()
–Getdents(), link(), unlink(), rename()
–Readlink(), symlink()
–Chown(), fchown(), lchown()
–Chmod(), fchmod(), utime()
–Stat(), fstat(), lstat(), acess()
–Open(), close(), creat(), umask()
–Dup(), dup2(), fcntl()
–Select(), poll()
–Truncate(), ftruncate()
–Lseek()
–Read(), write(), readv(), writev()
```


# POSIX I/O #


User-space programs interact with the file system API, the POSIX
I/O. Whenever they write data, read from files, manage directories,
mount devices, change metadata on files, etc..

This is the logical layer on top of it all, the one that interacts with
the user applications directly.

It manages the open file table entries, and per-process file descriptors.

It also provices security mechanism and protection, such as access
control list.

For example on the `open()` system call the file descriptor table
allocates a file descriptor which points to an entry in the global
file table which contains all the I/O byte offset related information,
where we are currently reading in the file. This global file table has a
pointer that points to the proper inode number in the inode table. And
then it goes down to the layer of the VFS to the file handling on the
related file system.

The POSIX I/O is great but sometimes criticized for what it's good at.

Because it has to pass through so many checks of metadata on multiple
layers and the page cache, it sometimes isn't the best alternative when
real time I/O is in need.

Although its strong point is consistency and portability.

I've linked an article in the show notes titled "What’s So Bad About
POSIX I/O?" it lists some reasons why for high performance I/O it
would not be that good. However, for higher speed would break a lot
of consistency.


# MANAGEMENT, COMMANDS, & FORENSIC #


If you want to know more about your data storage you'll have to dig into
the world of forensic.

I've linked a book in the show notes called "File System Forensic
Analysis", it's a great resource.

There are a bunch of open source tools that can be used to retrieve
information from a disk, for example the sleuthkit, which is a collection
of tools for forensic analysis.

Other useful tools such as `photorec` can be used in case of data
corruption to retrieve the files on a disk.

But as with anything that messes with your data storage be sure to do
backups before playing with them.


# Conclusion #


So this is it, you should now have a big gross overview of the whole
data storage architecture on Unix.

What you have to remember is that at every layer there's an encapsulation
and abstraction of the data passing through.

It all represents abstracted access to data.

From the disk to the drivers, to the block layer, to the file system,
to the virtual file system, to the POSIX file I/O.

As usual if you have something to add to the podcast or if you want
to correct a mistake then comment on the forums and contribute to the
discussion.

# Music #

Mosquito by Pk jazz Collective
<http://store.southerncitylab.net/track/mosquito>.

# References #


* <https://en.wikipedia.org/wiki/File:IO_stack_of_the_Linux_kernel.svg>
* <https://en.wikipedia.org/wiki/File_system>
* <https://help.ubuntu.com/community/LinuxFilesystemsExplained>
* <http://linuxfinances.info/info/fs.html>
* <https://msreekan.com/2012/06/07/file-system-loadable-kernel-module-lkm/>
* <https://msreekan.com/2015/04/24/linux-storage-cache/>
* <http://www.ufsexplorer.com/und_fs.php>
* <http://www.cs.cmu.edu/~410-s07/lectures/L27_Filesystem.pdf>
* <https://jkmaterials.yolasite.com/resources/materials/UNIX/UNIX_INTERNALS/UISVE/UNIT-III.pdf>
* <http://www.netbsd.org/docs/internals/en/netbsd-internals.html#chap-file-system>
* <http://www.porcupine.org/forensics/forensic-discovery/chapter3.html>
* <https://en.wikipedia.org/wiki/Cylinder-head-sector>
* <http://www.yolinux.com/TUTORIALS/LinuxTutorialSCSI.html>
* <http://www.tldp.org/HOWTO/html_single/SCSI-2.4-HOWTO/#intro>
* <https://unix.stackexchange.com/questions/144561/in-what-sense-does-sata-talk-scsi-how-much-is-shared-between-scsi-and-ata>
* <https://www.kernel.org/doc/htmldocs/libata/>
* <https://www.linuxquestions.org/questions/linux-general-1/sata-vs-scsi-for-a-server-387308-print/>
* <https://www.freebsd.org/doc/handbook/geom-glabel.html>
* <https://www.cyberciti.biz/faq/freebsd-hard-disk-information/>
* <https://www.freebsd.org/cgi/man.cgi?query=smartctl&manpath=FreeBSD+9.0-RELEASE+and+Ports&format=html>
* <http://nixdoc.net/man-pages/FreeBSD/ata.4.html>
* <https://www.freebsd.org/cgi/man.cgi?query=da&sektion=4>
* <http://www.webopedia.com/DidYouKnow/Computer_Science/sas_sata.asp>
* <https://insidehpc.com/2006/04/what-is-the-difference-between-scsi-and-ata/>
* <https://en.wikipedia.org/wiki/SCSI>
* <http://linuxmafia.com/faq/Hardware/sata.html>
* <https://en.wikipedia.org/wiki/Serial_Attached_SCSI>
* <https://en.wikipedia.org/wiki/Parallel_ATA>
* <https://en.wikipedia.org/wiki/Serial_ATA>
* <https://en.wikipedia.org/wiki/Industry_Standard_Architecture>
* <https://en.wikipedia.org/wiki/Logical_block_addressing>
* <https://www.freebsd.org/doc/en/books/arch-handbook/driverbasics-block.html>
* <https://en.wikipedia.org/wiki/Device_mapper>
* <https://en.wikipedia.org/wiki/Disk_partitioning>
* <https://en.wikipedia.org/wiki/Partition_type>
* <https://en.wikipedia.org/wiki/Partition_table>
* <https://en.wikipedia.org/wiki/Master_boot_record>
* <https://en.wikipedia.org/wiki/BSD_disklabel>
* <https://wiki.archlinux.org/index.php/LVM#Introduction>
* <https://wiki.archlinux.org/index.php/Software_RAID_and_LVM>
* <http://www.tldp.org/HOWTO/Linux+FreeBSD-2.html>
* <https://en.wikipedia.org/wiki/Logical_Volume_Manager_(Linux)>
* <https://en.wikipedia.org/wiki/Virtual_file_system>
* <https://en.wikipedia.org/wiki/Fragmentation_(computing)#Internal_fragmentation>
* <http://www.tldp.org/LDP/lki/lki-3.html>
* <http://learnlinuxconcepts.blogspot.com/2014/10/the-virtual-filesystem.html>
* <http://www.tldp.org/LDP/sag/html/buffer-cache.html>
* <https://www.ibm.com/developerworks/library/l-virtual-filesystem-switch/index.html>
* <https://en.wikipedia.org/wiki/Data_scrubbing>
* <https://en.wikipedia.org/wiki/Copy-on-write>
* <http://www.goop.org/~jeremy/userfs/>
* <https://en.wikipedia.org/wiki/File_descriptor>
* <http://linuxfinances.info/info/defrag.html>
* <http://www.tldp.org/LDP/tlk/fs/filesystem.html>
* <http://www.tldp.org/LDP/sag/html/filesystems.html>
* <http://man7.org/linux/man-pages/man5/filesystems.5.html>
* <http://edusagar.com/articles/view/22/Unix-File-System-internals>
* <http://www.cs.pomona.edu/~markk/filesystems/bsd.html>
* <https://en.wikipedia.org/wiki/Ext2>
* <http://e2fsprogs.sourceforge.net/ext2intro.html>
* <http://teaching.csse.uwa.edu.au/units/CITS2002/fs-ext2/ext2fs_1.html>
* <http://xpt.sourceforge.net/techdocs/nix/general/gnl10-SystemMaintain/ar01s06.html>
* <http://perl.plover.com/yak/ext2fs/>
* <https://en.wikipedia.org/wiki/Log-structured_File_System_(BSD)>
* <https://en.wikipedia.org/wiki/Procfs>
* <http://www.tldp.org/LDP/intro-linux/html/sect_03_01.html>
* <https://en.wikipedia.org/wiki/List_of_file_systems>
* <http://www.shub-internet.org/brad/FreeBSD/postmark.html>
* <https://en.wikipedia.org/wiki/Disk_sector>
* <https://en.wikipedia.org/wiki/Hard_disk_drive_performance_characteristics#Seek_time>
* <https://en.wikipedia.org/wiki/Block_suballocation>
* <https://en.wikipedia.org/wiki/Inode_pointer_structure>
* <https://en.wikipedia.org/wiki/Inode>
* <https://dlorch.github.io/hammer-linux/files/hammer-lorch.pdf>
* <http://www.osdevcon.org/2009/slides/zfs_internals_uli_graef.pdf>
* <https://en.wikipedia.org/wiki/ReiserFS>
* <https://en.wikipedia.org/wiki/HAMMER>
* <https://www.dragonflybsd.org/hammer/>
* <https://www.princeton.edu/~unix/Solaris/troubleshoot/zfs.html>
* <https://en.wikipedia.org/wiki/QNX4FS>
* <https://en.wikipedia.org/wiki/XFS>
* <https://en.wikipedia.org/wiki/ZFS>
* scsitools-gui
* <Installation: https://docs.freebsd.org/doc/7.4-RELEASE...ks.html&gt;
* <http://www.tutorialspoint.com/unix/pdf/unix-file-system.pdf>
* <https://en.wikipedia.org/wiki/PhotoRec>
* <https://en.wikipedia.org/wiki/GNU_Parted>
* <http://freecode.com/projects/fstransform>
* <http://www.cis.upenn.edu/~bcpierce/unison/>
* <https://en.wikipedia.org/wiki/Unix_File_System>
* <http://pages.cs.wisc.edu/~remzi/OSTEP/file-implementation.pdf>
* <http://www.scylladb.com/2017/10/05/io-access-methods-scylla/>
* <https://www.nextplatform.com/2017/09/11/whats-bad-posix-io/>
* <http://www.campus64.com/digital_learning/data/cyber_forensics_essentials/info_file_system_forensic_analysis.pdf>
* <https://opensource.com/article/18/4/ext4-filesystem>




josuah
I spent a pleasing hour, thank you.

If I understood it, there is quite a lot between the application (top), and the VFS (just under) that is not described on this diagram, (file table, with locks...).

I wanted to have quick access to all files names (through find /), and now I know that it is cached to the direntry cache of the VFS. It feels good to know where things goes. I will probably come back to these podcast as I need to check info back. Like for a lecture with an associated book :).

Code:
$ time find > /dev/null
    0m00.21s real     0m00.03s user     0m00.09s system

$ time find > /dev/null
    0m00.10s real     0m00.03s user     0m00.07s system
venam
(15-10-2017, 06:23 PM)josuah Wrote: If I understood it, there is quite a lot between the application (top), and the VFS (just under) that is not described on this diagram, (file table, with locks...).
The goal of the podcast was to go from the bottom layer to the top so that anyone could grossly grasp this kind of schema.
It seems like it's not doing that bad of a job at that.

Yes, what you're mentioning are kernel data structures.
This Linux Storage Stack Diagram focuses on storage and what you're mentioning is not really part of it.
There are more diagrams here:



budRich
I have missed the pod, glad your recording again! I always listen to your podcasts multiple times due to the high density of quality information. Excellent shownotes/linklist. Keep it up Venam, the Man!
venam
(16-10-2017, 09:48 PM)budRich Wrote: I have missed the pod, glad your recording again! I always listen to your podcasts multiple times due to the high density of quality information. Excellent shownotes/linklist. Keep it up Venam, the Man!

Feels good to hear that kind of feedback.

I had some trouble organizing the linklist for this episodes into categories like I normally do. While preparing it I wasn't sure of the order in which I was going to tackle it and the brainstorming became nasty.
venam
Someone recently asked after checking this podcast "But what and how do USB fall into that, I got a HDD over USB".

In the podcast I only went over the physical HDD directly connected via SCSI or ATA but it's mostly the same for other inputs.
On Linux it uses the LIO: https://en.wikipedia.org/wiki/LIO_(SCSI_target)

All those devices are called SCSI initiator/target: https://en.wikipedia.org/wiki/SCSI_initiator_and_target

What you can understand from this is that there's a new layer of translation.
josuah
(16-10-2017, 12:46 AM)venam Wrote:
(15-10-2017, 06:23 PM)josuah Wrote: If I understood it, there is quite a lot between the application (top), and the VFS (just under) that is not described on this diagram, (file table, with locks...).
The goal of the podcast was to go from the bottom layer to the top so that anyone could grossly grasp this kind of schema.
It seems like it's not doing that bad of a job at that.

Yes, what you're mentioning are kernel data structures.
This Linux Storage Stack Diagram focuses on storage and what you're mentioning is not really part of it.
There are more diagrams here:




Diagrams... Everywhere...

Thanks for opening thte knowledge tap. That is clear now.
venam
Another very useful command on Linux I forgot to mention is the device manager commands.
For example:
Code:
udevadm info --query=all /dev/sda1
Which returns a lot of the info we mentioned, hardware type, its configuration and caches, connector type, fs type, driver major & minor numbers, etc..
Mrat
You are amazing venam!

Readed part of the transcription, I'm going to listen to it tomorrow!




Members  |  Stats  |  Night Mode  |  Help